- "CONNECTS TO" is a required field.
- You must select at least 1 choice for TRIGGER BLADES.
SmartPin Adjustable Pointer
£14.99 – £43.99
Precisely adjustable pointer for reading the parallax wheels in different conditions. For temperature shifting scopes, light/dark environments, old eyes etc.
Fits 1″ / 30mm / 34mm / 36mm / 40mm scope tubes or 42-43 mm ocular tubes for shark fin wheels – and needs only 10×10 mm space in width and length as seen on the picture. With stainless steel screws and steel pins.
This pointer can be adjusted within 20 mm or 30 mm with a thumb screw, allowing precise and repeatable positioning of the pointer. The scale has 2 mm divisions. No need to fix and release, the pin has got some friction so it always stays where you set it with the screw, no accidental move (by your shooting jacket or rifle case).
The adjustable pointer comes with an additional pin 3 mm under the other one, for combining the effects (e.g. use the screw adjustment of the pointer to compensate scope temp shift and use the two pins for light and dark targets). If you need a longer or shaped pin, you can simply replace the original steel pins with any <1mm wire or paper clip.
New updated ring design is available. The same function but a better looking ring, scope tube protection, bolt/nut secured against falling out.
For more features and combinations with other scope ring features see Every Possible (And Impossible) Scope Ring Combination.
Additional information
Weight | 15 g |
---|---|
DIAMETER | 1" (25.4 mm), 30 mm, 34 mm, 36 mm, 40 mm, 42-43 mm |
SCALE LENGTH | Short (20 mm), Normal (30 mm) |
DESIGN | Old design, New design |
Only logged in customers who have purchased this product may leave a review.
Related Products
GAPacity Sidewheel + Free Pointer
This product has been discontinued. Check out the new design, the Composite series:
- Composite Parallax Wheels: 125mm and 150mm DualCore (round centered/excentric), 225mm effective diameter comma wheel.
- Composite Click Turret: 54 mm oversized turret, resettable without tool, wit or without bottoming ring.
- Composite Zoom Lever: stylish and handy zoom lever.
- All three in a bundle on a reduced price: Composite Scope Kit
Folding Windicator / Alligator Clip
Professional folding windicator with orange Nylon cord or alligator clips. Fits to any barrel or air cylinder (with the included adapter), 11mm dovetails, Picatinny/Weaver rails, standard UIT accessory rails, 1″ (25.4mm), 30mm and 34mm scope tubes.
The arm clicks into position when folded in or out (except for the scope ring versions). Ready to use with cable ties / bolts and cord, but of course you can replace the cord any time you like. Unbreakable, flexible, and only 7 grams. Made of high quality laser sintered Nylon, stainless steel nut and bolt.
NEW: also available with new design scope rings. For more features and combinations with other scope ring features see Every Possible (And Impossible) Scope Ring Combination.
NEW: all the windicators are available with alligator clips, too. See the options below.
Composite Click Turret
Stylish and professional oversized click turret, high quality laser sintered Nylon top with a massive grip. Easy re-setting without tools, internal cogs to keep the zero setting, 54mm outer diameter, 21mm high space for your click marks, bottoming function (on compatible scopes), mounts directly onto the existing turrets (except Falcon T models), leaves no mark on your scope.
- Composite Parallax Wheels: 82mm round, 125mm and 150mm DualCore (round centered/excentric), 229mm effective diameter comma wheel.
- Composite Click Turret: 54 mm oversized turret, resettable without tool, wit or without bottoming ring.
- Composite Zoom Lever: stylish and handy zoom lever.
- All three in a bundle on a reduced price: Composite Scope Kit
FlexiPoint Spare Blades
These items are only spare parts for my trigger system (in black colour only), and allow you to try different surfaces and shapes to make sure, which one fits you the best in practice.
If you’d like to have a complete trigger, please click here: FlexiPoint offset trigger.
For detailed information please click on the tabs below:
Ball trigger with a 5 and an 8 mm ball on the two ends. Ball triggers are fine because you’ll always have the same trigger weight, but it’s a severe problem that you can’t feel the direction of the pull. If you ask me, you should rather choose a round trigger instead from my standard blades, it’s much better. This Ball trigger is available in Offset version, too.
Small horizontal trigger with pyramids on both sides (fine and coarse). Similar to the ball but you can feel the direction of the pull.
These blades have a big round surface that fits to the fingertip. There are four different surfaces, they look quite similar but each version gives a totally different feel on the trigger, so you can choose the one that fits to your shooting style the best.
- ‘Centre’ gives a d=2 mm sharp point in the middle, giving a very precise feedback of the actual pull weight, the edge gives only a small hint of the right pull direction.
- ‘Deep’ follows the shape of the fingertip, giving a comfortable and evenly distributed contact on the whole surface.
- ‘Edge’ is for those who are after the right pull direction, combined with a comfortable feeling of the deeper middle surface.
- ‘Flat’ feels like a flat surface, simple and precise.
Traditional straight and curved blades, 8mm wide, 20mm high surface with vertical grooves, the middle height is marked with a horizontal groove.
EasyPin Extra Pointer
Adjustable angle scope pointer (10°–90° to the scope tube, two positions). Fits 1″ / 30mm / 34mm / 36mm / 40mm scope tubes, and needs only 10 mm space on the tube. The top is 11.5 mm above the tube in vertical pin position..
For parallax wheels and click turrets.
With stainless steel screws and steel pin. If you need a longer or shaped pin, you can simply replace the original pin with any <1mm wire.
New updated ring design is available. The same function but a better looking ring, scope tube protection, bolt/nut secured against falling out.
The 30/34mm new design pointers are available in a ‘Target’ version i.e. with two pointers, one for the elevation turret and another on on the side for the windage turret.
For more features and combinations with other scope ring features see Every Possible (And Impossible) Scope Ring Combination.
ZoomR Magnification Lever
A simple and streamlined design for those who want something more professional than those cheap fishing coasters. This zoom lever is worthy of your scopes and of the other Maestro Design accessories on your scope.
Fits to many scope models. 12 mm thick, lightweight, comfortable and sure grip in all conditions. Made of strong laser sintered Nylon or UV-stable ASA or PLA/PHA polymer (polished), with stainless steel screws.
All these zoom levers are in stock but please note that these are the last ones, this product has been discontinued.
Check out the new design, the Composite series:
- Composite Parallax Wheels: 125mm and 150mm DualCore (round centered/excentric), 225mm effective diameter comma wheel.
- Composite Click Turret: 54 mm oversized turret, resettable without tool, wit or without bottoming ring.
- Composite Zoom Lever: stylish and handy zoom lever.
- All three in a bundle on a reduced price: Composite Scope Kit
FWB Anti-POI-Shift Kit
The FWB Anti-POI-Shift Kit stands of two laser sintered Nylon parts, they look the same but they’re a bit different inside:
- One of them replaces the original A-clamp and holds only the cylinder and protects the barrel from accidental kicks but lets it free float.
- The other one goes to the joint of the air cylinder and the reg. It can be fixed onto the barrel by two symmetrical grub screws that push small Nylon parts to the barrel and thus don’t scratch its surface.
With stainless steel screws, all secured against falling out. Easy mounting (you’ll have to drill only a 5 mm hole).
For a perfect solution please see also: FWB Anti-POI-Shift Rail
Scorpion FT Hook Extras MK4
Extras and spare/replacement parts for the old Scorpion MK4 FT hook system.
Scorpion MK5 extra parts are here: Scorpion FT Hook Extras MK5
Fitting the hook to different stocks: see Scorpion Base Plates
Reviews
There are no reviews yet.